Terms of Services

Terms of Service

The content shown on TQS, Inc. and RS Distribution Inc. galleries are for informative nature only. This means that we can not provide any warranty regarding the accuracy of the photos. We allways recommend to visit our warehouse/showroom to confirm the slabs colors you are looking for.

The content shown on TQS, Inc. and RS Distribution Inc. galleries are for informative nature only. This means that we cannot provide any warranty regarding the accuracy of the photos. We always recommend to visit our warehouse/showroom to confirm the slabs colors you are looking for.

AVOID VOIDING THE WARRANTY

1. IMPORTANT: READ BEFORE CUTTING – SLOW-CUT MATERIAL

2. Ensure that the cutting table is perfectly level and flat to reduce the risk of cracking during the cutting process.

3. RS Distribution, Inc. is not liable for cracks that occur during fabrication due to improper cutting speed or leveling.

4. Whenever possible, cut from the outer edge of the slab toward the center. Once the cut has begun, avoid interrupting it.

5. Prevent fractures by drilling holes at inside corners to serve as radii; for example: sink cutouts, stove openings, pipe holes, and other voids.

6. All quartz material contains resin and must not be exposed to direct sunlight (UV rays). Such exposure may cause discoloration, which is not covered by the warranty.

7. RS DISTRIBUTION, INC. ASSUMES NO LIABILITY WHATSOEVER FOR DAMAGE TO THE MATERIAL RESULTING FROM FAILURE TO ADHERE TO THE FABRICATION PROTOCOLS DESCRIBED HEREIN.

8. THE PROTECTIVE PLASTIC FILM MUST BE REMOVED, AND THE MATERIAL MUST BE INSPECTED BEFORE PROCEEDING WITH CUTTING. VARIATIONS IN COLOR, SHADE, AND PATTERN ARE INHERENT TO THIS MATERIAL AND DO NOT AFFECT ITS PERFORMANCE. SUCH VARIATIONS DO NOT CONSTITUTE VALID GROUNDS FOR REQUESTING A REPLACEMENT.

WARNING: QUARTZ CONTAINS SILICA. CUTTING, POLISHING, OR DRILLING this product releases crystalline silica dust (SiO2) into the air, which is hazardous. Prolonged exposure to this dust without proper protection may cause serious illnesses such as pneumoconiosis, bronchitis, emphysema, etc. Further information and government regulations can be found at OSHA.GOV/SILICA-CRYSTALLINE

EVITA ANULAR LA GARANTÍA

1. IMPORTANTE: LEER ANTES DE CORTAR - MATERIAL DE CORTE LENTO

2. Asegúrese de que la mesa de corte esté perfectamente nivelada y plana para reducir el riesgo de grietas durante el proceso de corte.

3. RS Distribution, Inc. no es responsable de las grietas que se produzcan durante la fabricación debido a una velocidad o nivelación inadecuadas.

4. Siempre que sea posible, corte desde el exterior de la plancha hacia el centro. Una vez que empiece el corte evita interrumpirlo.

5. Evite las fracturas taladrando agujeros en las esquinas interiores que serán radios, por ejemplo: fregadero, estufa, plomería y otros huecos.

6. Todo material de cuarzo contiene resina y no puede exponerse al sol (rayos uv). Eso podría cambiar el color y no lo cubre la garantía.

7. RS DISTRIBUTION, INC. NO SE RESPONSABILIZA POR DAÑOS AL MATERIAL POR NO SEGUIR LOS PROTOCOLOS DE FABRICACIÓN EXPRESADOS AQUÍ.

8. EL PLÁSTICO PROTECTOR DEBE SER REMOVIDO Y EL MATERIAL DEBER SER INSPECCIONADO ANTES DEL CORTE. LAS VARIACIONES EN COLOR, SOMBRA Y PATRÓN SON INHERENTES A ESTE MATERIAL Y NO AFECTAN SU RENDIMIENTO. ESTAS VARIACIONES NO CALIFICAN PARA EL REEMPLAZO.


ADVERTENCIA: EL CUARZO CONTIENE SÍLICA. AL CORTAR, PULIR O PERFORAR ESTE PRODUCTO, SE LIBERA AL AIRE EL PELIGROSO POLVO DE SÍLICA CRISTALINO (SiO2). LA EXPOSICIÓN PROLONGADA SIN PROTECCIÓN A ESTE POLVO PUEDE CAUSAR ENFERMEDADES GRAVES COMO NEUMOCONIOSIS, BRONQUITIS, ENFISEMA, ETC. SE PUEDE ENCONTRAR MÁS INFORMACIÓN Y REGULACIONES GUBERNAMENTALES EN OSHA.GOV/SILICA-CRYSTALLINE

Copyright 2026. RSD Distribution Inc.. All Rights Reserved. D4UW.COM